Liberia, Rotary Drilling Rigs, Rotary Drilling Rig, Rotary Drillingrigs, Rotary Drilling, Rotary Rig, Direct Rotary Drilling Rigs, Direct Mud Rotary Drilling Rigs, Rotary Drilling Rigs Manufacturers, Rotary Drilling Rigs Exporters, Rotary Drilling Rigs Suppliers, Rotary Drilling Rigs For Sale

SPECIFICATIONS
Hammer Name	P45 Hammer	P45 LT Hammer	P45 Sub. Hammer
Part Number	H45P	H45PLT	H45PS
Outside Dia (mm)	96.00	96.00	96.00
Recomm. Bit size (mm)	114.30-130.00	114.30-130.00	114.30-130.00
To Sub Thread (IN)	2-3/8 Reg box	2-3/8 Reg box	2-3/8 Reg box
Ham. Wt. without Bit (Kg.)	42.00	44.00	43.50
Total Len. without Bit (mm)	994.0	1070.0	1044.0
Wrench Flat (mm)	74.00	74.00	74.00
Working Pressure (Bar)	7.5-14.5	7.5-14.5	7.5-14.5

Component Name	H45P	H45PLT	H45PS
Piston Case / Std Barrel	HB45P	HB45PLTLT	HB45PS
Std Piston	HP45P	HP45PLT	HP45PS
Std Std Seat Valve	HSV45P	HSV45PLTLT	HSV45PS
Std Std Chest Valve	HCV45P	HCV45PLTLT	HCV45PS
Std Liner	HL45P	HL45PLT	HL45PS
Top Sub / Std Back Head	HC45P	HC45PLT	HC45PS
Driver Sub / Std Front Chuck	HFC45P	HFC45PLT	HFC45PS
Std Flapper Valve	HFV45P	HFV45PLT	HFV45PS
Std Valve Guide	HVG45P	HVG45PLT	HVG45PS
Guide Sleeve / Std Assembly Bush	HAB45P	HAB45PLT	HAB45PS
Bit Retainer Ring / Std Bit Lock	HBL45P	HBL45PLT	HBL45PS
Dart / Std Check Valve	HCKV45P	HCKV45PLT	HCKVC45PS
Std Check Valve Cap	HCVC45P	HCVC45PLT	HCVC45PS
Retainer Pin / Std Dowell Pin	HDP45P	HDP45PLT	HDP45PS
Std Spring	HS45P	HS45PLT	HS45PS
Std Washer	HMW45P	HMW45PLT	HMW45PS
Std Stem Bush	HSB45P	HSB45PLT	HSB45PS
O Ring / Std Bit Lock O Ring	HBR45P	HBR45PLT	HBR45PS
Std Blocking Choke	HBC45P	HBC45PLT	HBC45PS
Std Front Chuck Rubber Cap	HFCRC45P	HFCRC45PLT	HFCRC45PS
Std Back Head Rubber Cap	HCRC45P	HCRC45PLT	HCRC45PS
SPECIAL FEATURES • For use in hard rock application • Suitable for Horizontal & Vertical drilling operations • Excellent under water characteristics • Able to work on any strata • Less maintenance
GENERAL CARE Before shutting down at the end of each shift, we recommend the following procedures: Flush Hammer with air/water for a few minutes, then turn off water injection Flush Hammer with air/oil for a few minutes. This will coat the internal Hammer parts preventing corrosion/rust. Never leave the tool in a wet / muddy hole. Pull back from bottom as far as necessary to prevent the Hammer sitting under water. It is also good practice to pour at least half a litre of oil down the drill at start up of a new shift. If the Hammer is removed from the drill rig for any reason, it is wise to pour a quantity of oil into it and block both ends, providing the flushing as outlined in steps one and two above have been carried out. If steps one and two have not been carried out the Hammer should be stripped, cleaned and oiled before being stored.